Ajouter à la Wishlist
Manufacturer : GEPRC / Référence : GP107501

Taker F722 BLS 100A 8S Stack By GEPRC

Hors stock
€159.90
Out-of-Stock Notify me when the product is available again

16 points loyalty thanks to this product

Thanks to our loyalty program, you collect 1 point with each 10 euros you spend. The points will be collected in your personal account. 1 loyalty point will count for your voucher as 0.2 euros.

Shipping costs from 49€ pour France
Same day shipping for orders placed before 3:30pm (Monday to Friday)

Related accessories

Related products

Technical characteristics

The GEPRC TAKER F722 100A stack supports 3-8S LiPo voltage, mounts in a 30.5x30.5mm format, and is compatible with the DJI O4 air unit.

It consists of a TAKER F722 8S flight controller equipped with an ICM42688P gyro, a 16M blackbox, a barometer, a 5V 3A and 12V 3A dual BEC, and 6 UARTs.

The TAKER H100 8S BLHeli_S 4-in-1 ESC supports 100A current and Dshot 150/300/600 protocols.

Upon receiving your FC,please connect to USB and calibrate before continuing to build and solder to it.

TAKER F722 8S FC

  • MCU: STM32F722
  • IMU: ICM42688-P(SPI)
  • Air Unit Connection: Direct plugs into DJI Air Unit
  • Black Box: 16M onboard
  • USB Interface: Type-C
  • Barometer: Supported
  • OSD: BetaFlight OSD w/ AT7456E chip
  • BEC: 5V@3A,12V@3A dual BEC
  • Firmware Target: TAKERF722SE
  • Dimension: 38.5×38.5mm,
  • Mounfing Hole Size: 30.5×30.5mm，φ4mm hole becomes φ3mm after using a silicone shock-absorbing circle
  • Input Voltage: 3-8S LiPo
  • UART: 6 UARTs
  • Power Filter: Integrated LC filter
  • Weight: 8.1g

TAKER H100 8S BLS 4in1 ESC

  • Input Voltage: 3-8S Lipo
  • Ammeter: Support
  • Calibration value: 200
  • Continue Current: 100A
  • Burst Current: 105A (5 seconds)
  • Support Protocol: Dshot 150/300/600
  • Size: 56.3*61.1 mm; hole: 30.5×30.5 mm; φ4 mm hole becomes φ3mm after using the silicone shock-absorbing ring.
  • Weight: 28.8g
  • Target: B_X_30

Bullet points

  • Uses the mainstream STM32F722 chip
  • Equipped with the latest 42688-P gyroscope 3.16M onboard black box storage
  • Integrated LC filter
  • Upgraded Type-C USB interface
  • Directly plugs into the DJI Air Unit
  • Paired with the TAKER H100_8S_BLS 100A 4IN1 ESC, providing a smooth flying experience
  • Simple and efficient installation method with shock absorbers for stable gyroscope performance
  • Dual independent BECs: 12V@3A and 5V@3A
  • Supports 8S Lipo batteries
  • Support direct insertion of 8 motors

Included

  • 1x FC board
  • 1x ESC board
  • 1x Capacitor
  • 1x O3 3-in-1 connection cable
  • 2x FC adapter cable
  • 1x sh1.0 4pin silicone cable
  • 1x Camera connection cable
  • 1x VTX connection cable
  • 1x XT90 power cable
  • 4x M3*30 screws
  • 4x M3*25 screws
  • 8x Nylon nuts
  • 12x Silicone anti-shake pads
Voir plus

Découvrez aussi