KAKUTE F7
KAKUTE F7
KAKUTE F7
KAKUTE F7
KAKUTE F7
KAKUTE F7
Manufacturer : Holybro / Référence : KAKUTE-F7

KAKUTE F7 V1.5

€39.08
Same Day Shipping

4 points loyalty thanks to this product

Thanks to our loyalty program, you collect 1 point with each 10 euros you spend. The points will be collected in your personal account. 1 loyalty point will count for your voucher as 0.2 euros.

Frais de port à partir de 49e pour la France
Expédition le jour même pour les commandes passées avant 15h30 (du lundi au vendredi)

Caractéristiques techniques

The Holybro Kakute F7 flight controller makes it easy to build your multirotor.

Upon receiving your FC,please connect to USB and calibrate before continuing to build and solder to it.

The Holybro Kakute F7 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and on-screen display (OSD) in one. The Kakute F7’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy.

IMU updated to MPU6000,Re-designed and more reliable damping structure

Features

  • Supports Betaflight, Butterflight, and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • High-performance / low-noise / high sensitivity IMU. MPU6000 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.
  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F745 32-bit processor
  • IMU: MPU6000 (SPI)
  • Barometer: BMP280
  • Current Sensor: Approximately 130 amps maximum measurable value
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 6 hardware UARTS (UART1,2,3,4,6,7)
  • All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • TF card for Blackbox logging
  • Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 9g

Package Includes

  •    FC board *1
  •    Foam*1
  •    JST SH 8pin 150mm cable*1  
Voir plus

Avis clients

5/5 (7 avis)
Par le 24/10/2020

A Class !

Par le 23/10/2020

Réponds à mes attentes

Par le 10/04/2020

Bonnes performances, accès facile et connexion bien repérées sur la carte

Par le 10/04/2020

OK RAS ; je me met au montage.

Par le 27/03/2020

Great FC

Par le 08/02/2020

Ottima fc

Par le 14/12/2018

ma première elle a l'air bien

Frais de port offerts
Frais de port offerts À partir de 49€ pour toute livraison en France métropolitaine
Livraison en 24/48h
Livraison en 24/48h Pour toutes commandes passées avant 15h30 (du lundi au vendredi)
Paiement sécurisé
Paiement sécurisé Tous vos paiements sur Drone FPV Racer sont 100% sécurisés
Service client
Service client Un conseil ? Une question ? Visitez notre FAQ