ETHIX MR STEELE STOUT MOTOR V3
ETHIX MR STEELE STOUT MOTOR V3
ETHIX MR STEELE STOUT MOTOR V3
ETHIX MR STEELE STOUT MOTOR V3
ETHIX MR STEELE STOUT MOTOR V3
ETHIX MR STEELE STOUT MOTOR V3
Manufacturer : Team BlackSheep / Référence : TBS-STOUT-V3

ETHIX MR STEELE STOUT MOTOR V3

€24.92
Last items in stock

3 points loyalty thanks to this product

Thanks to our loyalty program, you collect 1 point with each 10 euros you spend. The points will be collected in your personal account. 1 loyalty point will count for your voucher as 0.2 euros.

Frais de port à partir de 49e pour la France
Expédition le jour même pour les commandes passées avant 15h30 (du lundi au vendredi)

Accessoires associés

Caractéristiques techniques

The brand new Ethix Mr. Steele V3 (Stout) motor for 6S freestyle glory!

Introducing the third iteration of the Mr Steele motor line. This well-refined piece of kit is built upon the success of its predecessors and tuned for an even higher flight envelope. The same beloved 2306 stator is in play but this time with a beefier and much smoother 9mm ball bearing (up 2mm from the previous 7mm). This allows for a thicker overall shaft adding substantial durability and more material to dissipate heat built up from consistent power-hungry abusive rippers.

This motor is also offered in a slightly higher KV for its 6S variant: 50KV up from the V2 1700KV Stout. The increase in KV adds just enough more power without dipping into the red zone of diminishing returns on efficiency. So, it's just as efficient but with more pop. 

Featuring a completely redesigned motor bell design with a recessed 6 spoke design, allows for a lower profile bell and more modern look. The lower profile design has less wind resistance and a lower center of mass, assisting throttle response. On a side note, the recessed spokes also aid massively in the overall durability of the bell itself. This is seriously one tough little motor. 

All of these amazing new features and we were still able to keep the weight under 30g this motor comes in at 29g with the full length of wire and low profile plastic pants.

While the pants remain interchangeable with V1/V2, the V3 stator and bell is only compatible with other V3 models. You can swap SILK N48 magnet bells out for STOUT N52 magnet bells (added power and response). But since we went with a thicker shaft, these will NOT be compatible with previous generation Steele motor parts. This is a bummer, but to innovate sometimes you have to change. 

These motors are offered in:

SILK - 2306 2345KV N48 magnets recommended but not limited to 4/5S 5” freestyle mini quads.

STOUT - 2306 1750KV N52 magnets recommended for but not limited to 6S 5” freestyle mini quad setups. 

Voir plus

Avis clients

4.6/5 (13 avis)
Par le 06/11/2020

Superbement magnifique.

Par le 01/11/2020

Delicati....forse troppo

Par le 08/10/2020

all good

Par le 19/08/2020

Moteur facile et smooth

Par le 14/07/2020

Smooth freestyle motor with great response

Par le 14/07/2020

Un des moteurs a brûlé en même temps que les esc

Par le 07/03/2020

Satisfait

Par le 19/02/2020

Excellent

Par le 02/02/2020

very good motor

Par le 22/01/2020

Motori ottimi e molto fluidi

Par le 22/12/2019

Che dire.. se li usa Steele saranno ottimi

Par le 14/11/2019

Solide et efficace.

Par le 18/10/2019

ils sont de bien meilleure qualité que les précédentes générations de moteurs steele, les roulements plus gros y sont certainement pour beaucoup, pas de bruit parasite comme sur les anciens :) par contre mauvaise surprise, un kit de visserie manquait dans une boite ( le sachet n'avait que les caches plastiques )